1 Pneumatic Fender
Three(3) sets for working Yokohama type fenders shall be provided on board for ship-to-ship mooring. The nominal size offender shall be Dia. 4.5m X 7m. 3 套工作用 Yokohama 形式的充气碰垫需要提供，用于船与船对驳操作。充气碰垫的名 义尺寸为φ4.5m X 7m。
Fender needs to be made into milk-white without tyre net. 充气碰垫需要制作成奶白色，不需要配置轮胎网。
An additional rubber layer (15~20mm thickness) shall be provided outside fender. Rubber layer shall be wrapped around the fender before vulcanization. After vulcanization, the rubber layer and fender shall be merged into a whole. 充气碰垫外面设置一圈 15~20mm 保护橡胶层。橡胶层应在硫化之前包裹在充气碰垫外 部。硫化完成后，橡胶层与碰垫融合成一个整体
The number of pneumatic fender synthetic tire cord layer shall be increased 1~2 layers in additional to the ISO standard number, in order to increase the impact resistance. 充气碰垫合成轮胎帘线的层数，应该在 ISO 标准层数的基础上增加 1~2 层，以增加碰 垫抗冲击的能力。
Fender dimension tolerance shall be controlled within ±3%. 充气碰垫的尺寸偏差应该控制在±3%范围内。
The weight list of every pneumatic fender parts shall be provided on TA. The total weight of one fender shall be less than 8 Tons. 充气碰垫各部件的重量清单应该在技术协议中提供。单个碰垫的总重应不超过 8T。
Pneumatic fenders should comply with ISO 17357-1 2014. 充气碰垫应该满足 ISO 17357-1 2014 的要求。
Fender internal pressure at 0% deflection to be 50kPa. Safety valve to be provided 在 0%变形时的碰垫内部压力为 50kPa。提供安全阀。
The prototype certificate which confirms successful results of the tests which are evaluated by a major classification society shall be provided. 厂家应提供由主要船级社评估出具的，证明碰垫原型试验数据有效的证书。
The inspection and evaluation certificate for the ordered fenders carried out by BV shall be provided. 厂家应提供由 BV 出具的对产品碰垫进行的检验及评估的产品证书。
Performance curve which shown the relationship between deflection percentage, reaction force, inner pressure and energy absorption shall be provided in TA. 技术协议中应提供碰垫的性能曲线，反映变形百分率、反力、内部压力及吸能值之间的 相互关系。
Fender shall be marked clearly in order to be easily distinguished by crew. 充气碰垫上应该有醒目的编号标记，以方便船员区分。
A handling / storage / packing recommendation, maintenance manual and operation procedure shall be provided by maker. 起吊/储存/包装建议、维护保养手册以及操作程序应由厂家提供。
The flange offender shall be galvanized to ensure that it is resistant to corrosion by sea water. 充气碰垫的法兰需要进行热镀锌处理，保证能够抵抗海水的腐蚀。
The swivel and shackles for fenders (galvanized) shall be rotated freely and will not be blocked by fender flange. 碰垫的转环和卸扣(镀锌)应能够自由旋转并不受碰垫法兰阻挡。
SUS316 air valve and safety valve shall be well protected to avoid damage when handling. SUS316 充气阀和安全阀应该有良好的保护，以避免吊运时损坏。
.
The following spare part and tools to be provided: 以下备件及工具需要提供： No. | Name of spare parts and tool | Qty. (per vessel) | | | | | | | | | | | | | | | |
2.2 Baby Fender
Two(2) baby fenders (Dia.0.7m X 1.5m) without chain net to be provided at bow. 首部提供两个小的充气碰垫 ( φ0.7m X 1.5m），不配轮胎网。
2.3 Other Requirement
Racks for fender ’s storage shall be provided by yard. 充气碰垫的储存架由船厂提供。
The third-party inspection report which confirms the toxic and hazardous substances content meets No. 1257/2013 ship recycling Regulation (EU) shall be provided by maker. 厂家应提供有毒有害物质含量满足欧盟（EU）1257/2013 船舶回收法规的第三方检测报告。
Unless otherwise mentioned in this technical agreement, the technical requirement in this agreement is to be same as finalized technical requirement for ships H1870A. The finalized technical requirement includes but not limited to order specification, technical agreement, amendment to technical agreement, memorandum, approved comment and confirmed email etc. 除非在本协议中另行说明，本系列船的技术要求应与 H1870A 船最终确认的技术要求一致，最 终确认的技术要求包括但不限于订货说明书、技术协议、 补充协议、备忘、退审意见、确认的 邮件等。
| 
