上海振华迪拜5000T起重船ZPMC1142橡胶护舷、靠球技术规格书

jimosea

上海振华迪拜5000T起重船ZPMC1142橡胶

护舷

、

靠球

技术规格书

充气橡胶护舷 Pneumatic Rubber Fender
2.1 产品规格 Products Requirements：
名称：充气橡胶护舷:Φ2500mm×L5500mm
Name: Pneumatic Rubber Fender:Φ2500mm×L5500mm
类型：50 型Ⅱ型（悬挂式）
TYPE: 50- Type II (suspension type)
执行标准：GB/T 21482-2019
Standard: GB/T 21482-2019
数量：4 套
QTY.：4 sets
2.2 使用环境条件 Environmental Conditions
1）使用介质：海水；
Use medium：seawater
2）环境温度：16℃＋55℃
Environmental temperature: 16℃＋55℃
3）工作条件：充气橡胶护舷在海水中满足船舶靠泊作业使用。
Working requirement: pneumatic rubber fender following barge mooring working in seawater.
2.3 技术要求 Technical Requirement
1) 充气橡胶护舷主体材料为橡胶，骨架层为挂胶帘线，内外层橡胶要保证在使用期限内保
持足够的硬度，耐刺，耐酸碱，耐臭氧老化；
Main material is rubber, the skeleton layer is cord ply, the inside-outside glue layer need to be
confirmed which will keep enough hardness, stab-resistance, acid and alkali resistant and Ozone
aging resistance in service life.
2) 充气橡胶护舷所用材料的物理性能、主要成分、力学性能指标等要达到本规格书要求（见
表 1）和 GB/T 21482-2019 标准要求；
The physical performance, main material ,force performance and other index of module
pneumatic rubber fender’s material need to meet the this document(see the table 1) and GB/T
21482-2019 standard requirements.
3) 充气橡胶护舷材料需耐海水腐蚀；
The pneumatic rubber fender material needs to be seawater corrosion resistance.
4) 充气橡胶护舷的两端 Q235 热镀锌吊环和卸扣强度需达到技术要求，满足吊运悬挂使用；
The strength of Q235 HDG lifting rings and shackles at both sides of pneumatic rubber fender
are should be meet the technical requirements and could satisfy the handling.
5) 球体外观要求光滑、平整，可以有模具缝，但不能有气泡和橡胶片搭接；
The surface of the sphere should be flush and flat which could have mould gap but can’t havebubble and rubbers joint.
6) 球体内外法兰和螺栓需使用 SUS316L 材质，防海水腐蚀；
The flange of sphere inside and outside bolts need to be SUS316L to avoid seawater corrosion.
7) 球体需高温高压硫化，内层胶、帘线层和外层胶三个结构层之间不得有任何脱层和间隙；
Sphere should be vulcanized in high temperature and high pressure condition,and the three
different layer, inside glue, cord ply and outside glue, can’t have any delaminating or gap.
8) 球体两端需有带有规格型号，出厂日期、出厂编号、工作压力等标识，标识为永久性；
On both side of sphere need to add forever marking which include type, date of production,
factory number, working pressure and other marking.
9) 充气橡胶护舷被压缩变形 60%时反力和吸能应满足性能要求；
When the module pneumatic rubber fender is stressed 60% transformation, the reinforce and
energy absorption should meet the performance requirements.
10) 安全阀压力上限 175Kpa，球体内压力超过 175Kpa 时安全阀必须自动开启泄压。初充气
压力 50Kpa,安全阀设定压力 175Kpa；排气压力在 175Kpa 时，安全阀流量为 750 立方米
/h；
The upper limit pressure for safety valve is 175Kpa, and the valve will auto release pressure
when the inside pressure of sphere exceed 175Kpa. The pressure is 50Kpa at first filling, and the
safety valve set pressure at 175Kpa. When venting pressure is 175Kpa, the flow valve is 750
stere per hour.



轮胎护舷 Tire Fender
4.1 产品规格 Product Specification：
执行标准：GB/T 2980-2018
Standard: GB/T 2980-2018
轮胎护舷直径：φ1615mm，断面宽度：595mm，数量：16 套。
Tire Fender diameter: φ1615mm, Section Width: about 595mm，QTY.： 16 sets.
4.2 技术要求 Technical Requirements：
1) 轮胎护舷样式见下图；
The detail of tire fender see the following drawing；






D 型护舷 D-shape rubber Fender
3.1 产品规格 Product Specification：
D 橡胶护舷：400x400xL：~7.1 米（8 条）、~5.8 米（2 条）、6.8 米（2 条）
D-Shape rubber Fender: 400x400xL：~7.1m（8 sets）、~5.8m（2 sets）、6.8m（2 sets）
执行标准：HG/T 2866-2016
Standard: HG/T 2866-2016
3.2 技术要求 Technical Requirements：
压缩 Stress
型号 Type
设计压缩变形 40%
Design Compression Deformation 40%
反力 Reaction
KN/M
吸能量 Energy
Absorption
KN-M/M
D 型 400H
D-Shape 400H
≤202
≥14.5
1) 性能公差±10%；
The tolerance of performance:±10%；
2) 数值为每米数值；
The number of table is per meter；
3) 按图提供所有 D 型护舷的 SS316L 紧固件；
All SS316L fasteners of D-shape rubber fender should be provided according to the DWG;
4) D 型护舷需厂家预弯出厂；
D-shape fenders need to be pre-bended before supply.